I've been trying to install Arch Linux. After the installation, it shows the BIOS screen and after that there just comes a message that says 'No bootable device found'. I have retried the whole scenario now some times, still it just shows the same message. At installing, I have followed the Unofficial Beginner's Guide from the ArchLinux wiki. Here is what I did: First of all, I wiped the hard drive (on which before the wipe was Windows Vista installed) and put GPT on it by using gdisk. Became a bit long for comment. Arch Linux Easy InstallThis is not directly related, but only to explain the aa55 comment. When the Basic Input/Output System (BIOS) starts it does a Power-On Self Test (POST), check hardware etc. Then it looks for devices that are both bootable and active by order given by CMOS (Your configuration in BIOS – which in turn is given by a Complementary Metal Oxide Semiconductor). When it finds a disk that has 0xaa55 at offset 510 it loads that section of the disk, (sector 1), into memory and leave control to it on address 0x00000 of that code. Those 512 bytes are the Master Boot Record (MBR). That code, in this case ' GRUB - boot', check various bytes of these 512 in addition to ask BIOS for various information. In this process it locates which disk has rest of GRUB and load that section of the disk into memory – then that part of code gets control. That one mounts kernel etc. Arch Linux Installing PackagesAnd leaves control to that. Using GPT the image GRUB loads from within MBR is located in the bios_grub partition, - which you have, and is big enough, etc., so can't see how that could be wrong. On 'No bootable device found.' Message from BIOS – one can have the case that MBR of boot disk is corrupted, if MBR ends in 0xaa55 and the MBR is corrupt one usually get an other error - or the system simply hangs. This is weird. I notice you have no partition marked as 'boot'. Using GPT that is correct, - but, though it is forbidden, you could try to flag one e.g. Sda5 as boot. In gparted: (learned that (g)parted also alter GPT which whan do not want)fdisk: # Toggle bootable: a [DISK NUMBER] # Check (could be an asterisk marking boot partition): p # Save changes: w It could be that your BIOS is doing more then it should and checking the partition table in MBR. EDIT – Update to comment: AFAIK it doesn't matter which one you set as it is not actually used. I have an arch linux VM running on the retina mac book pro. I would like to be able to see the Parallels Tools multi monitor support work for Arch as well as it does on Ubuntu 14.04 LTS, or for Windows 10. Installing Arch Linux In Parallels 10 DownloadSep 11, 2015 I have an arch linux VM running on the retina mac book pro. I would like to be able to see the Parallels Tools multi monitor support work for Arch as well as it. Make a bootable installation media for Arch Linux This laptop doesn’t have any CD/DVD drive so the first thing is to make a bootable USB drive. Boot into Windows 10. Aug 22, 2018 - Here are the best Linux distros to install on a Mac. A change, and while Windows 10 is an option, Linux can also freshen up your workstation. Arch Linux is known among Linux enthusiasts for its speed and performance,. Point being, for whom ever say no 'bootable device found', they shall be satisfied. The sda1 is not a boot partition in the traditional sense, but space for GRUB boot files. In a traditional partition layout (not GPT) you have typically something like: 0x000 [Master Boot Record]. Download a perfect optimizer install this error repair tool. I may be wrong and haven't done the right thing, but I've had the same problem as you at first. Installing Arch Linux In Parallels 10 FreeAfter a while, I've found that GRUB has to have a 512MB EFI partition, with a vfat filesystem. This is in case you install your system as EFI: For EFI, you are looking for a small (512 MiB or less) partition with a vfat file system and the boot flag enabled. This means that you have to anticipate this fact when creating your partitions. While doing so (with cfdisk for example), you'll have to set your /dev/sdX1 as EFI, then format it to a FAT32 filesystem (with the command mkfs.vfat -F32 /dev/sdX1 during the installation process). Only then grub will be recognized. I assume Syslinux can work with your ext2 partition though, if you feel like trying it. If you don't install Arch as EFI, you probably can check on the wiki whatsoever. I'm not able to help any further in this case. I know this post is old, but this is in case someone comes here and hopes to find a solution.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |